Nano F4 Series High Pressure Stainless Steel Filters
flow capacity: 28 - 2,000 scfm
The nano F4 range of high pressure stainless steel filters consists of 21 models across three pressure ranges offering flow ratings up to 2000 scfm and pressure ratings up to 5000 psig. Manufactured from high grade 316 stainless steel and corrosive resistant coated carbon steel, the nano F4 filters are precision engineered with high pressure applications in mind. The 725 psig range incorporates an innovative push-fit element design to ensure optimum sealing and mechanical strength. Filter elements are color coded for easy identification. The 1450 and 5000 psig ranges incorporate elements with corrosion resistant stainless steel end caps. A wide selection of filtration grades as well as a water separator option. Filtration grades include M25, M1, M01 and AC which provide a solution for the most demanding applications. The custom engineered filter media is designed to provide low air velocity preventing oil carry over for high efficiency filtration with minimal pressure drop.
• Manufactured in an ISO 9001 approved facility and tested in accordance with ISO 8573-1:2010.
• install with air flow inside to outside for coalescing filtration and outside to inside for dry particulate filtration
• differential pressure indicator not included
*Scroll to the right on mobile to see entire chart
Model
replacement element
Inlet & Outlet NPT
rated flow1
scfm
Nm3/h
N50SS (725 psig)
N50SS 0060 (grade)
E50SS 0060 (grade)
¼"
60
100
N50SS 0120 (grade)
E50SS 0120 (grade)
⅜"
120
200
N50SS 0200 (grade)
E50SS 0200 (grade)
½"
200
340
N50SS 0300 (grade)
E50SS 0300 (grade)
¾"
300
500
N50SS 0600 (grade)
E50SS 0600 (grade)
1"
600
1000
N50SS 1000 (grade)
E50SS 1000 (grade)
1½"
1000
1700
N50SS 1200 (grade)
E50SS 1200 (grade)
2"
1200
2040
N50SS 2000 (grade)
E50SS 2000 (grade)
2"
2000
3400
N100SS (1450 psig)
N100SS 0060 (grade)
E100SS 0060 (grade)
¼"
60
100
N100SS 0185 (grade)
E100SS 0185 (grade)
½"
185
315
N100SS 0270 (grade)
E100SS 0270 (grade)
¾"
270
460
N100SS 0400 (grade)
E100SS 0400 (grade)
1"
400
680
N100SS 0700 (grade)
E100SS 0700 (grade)
1"
700
1200
N100SS 1000 (grade)
E100SS 1000 (grade)
1½"
1000
1700
N100SS 2000 (grade)
E100SS 2000 (grade)
2"
2000
3400
N350SS (5000 psig)
N350SS 0028 (grade)
E350SS 0028 (grade)
¼"
28
48
N350SS 0067 (grade)
E350SS 0067 (grade)
¼"
67
111
N350SS 0150 (grade)
E350SS 0150 (grade)
½"
150
255
N350SS 0300 (grade)
E350SS 0300 (grade)
¾"
300
510
N350SS 0445 (grade)
E350SS 0445 (grade)
1"
445
750
N350SS 0775 (grade)
E350SS 0775 (grade)
1"
775
1330
(1) at 725, 1450 or 5000 psig as applicable. For all other pressures, refer to the pressure correction factor table
*Scroll to the right on mobile to see entire chart
Specifications
N50SS
N100SS
N350SS
design operating pressure range
0 to 725 psig
0 to 1450 psig
0 to 5000 psig
condensate drain (included)
manual ball valve
housing material
316 stainless steel
*Scroll to the right on mobile to see entire chart
element performance
M25
M5
M1
M01
AC2
particle removal (microns)
25
5
1
0.01
-
max oil carry over at 68°F (ppm or mg/m3)
10
5
0.1
0.01
0.003
recommended operating temp range (°F)
35 - 212
35 - 212
35 - 212
35 - 212
35 - 77
design operating temperature range (°F)
35 - 248
35 - 248
35 - 248
35 - 248
35 - 122
(2) Activated carbon filters must always be installed immediately downstream of a M01 coalescing filter.
They will not remove carbon monoxide (CO) or carbon dioxide (C02) and are not suitable for breathing
air applications. The life of the element decreases as the inlet temperature increases. They are not
recommended for temperatures above 77°F. As a maximum, activated carbon elements should be replaced every 1000 hours or 6 months, whichever is shorter.
AirDryerTech.com is owned and operated by mdi, Manufacturers Distributor, Inc. mdi is an Authorized Pneumatech and Nano Distributor. Click Here to view the mdi Line Sheet.
Click Here to view the mdi Line Sheet.